R-100 4X4

[Jesse Stewart]

Anybody know what this switch controls ??

 

[FDChappie]

That looks like a fuel tank selector.

 

[Jesse Stewart]

Found a NOS one ...

I have the og left tank and a aftermarket 30 ga bed tank ...
Don't have the right tank, can't find one ..
Been thinking about taking another left tank and move the filler neck ..

There's a right side aux tank out there somewhere with my name on it ... I just haven't run up on it yet ..
Not looking forward to all the work it will take to convert a left side tank into a right side ..

 

[Jesse Stewart]

Thought it would be a good idea to slow down the rust .. Backside seen Por 15 applied ..

Getting closer to shooting the base coat ..

 

[Jesse Stewart]

Last check for fit ..

 

[Jesse Stewart]

More dash work ..

Was needing to mount the traffic viewer..
No way I was going to drill a hole in the dash ... "No Sir"

There are two factory drilled holes for the optional electric wipers, my truck came stock with vacuum, had push in cap plugs in those two holes .. Looked a bit tacky to me so I installed the factory bolts & cup washers after being dipped ...

There was the hole for the viewer ...

Needed a flat surface for the viewer's mount, just need to get a M5 X 0.8 thread down in it ..

I'm calling that done ..

 

[Jesse Stewart]

Fit is good ... Got a few holes to cut ..

 

[Jesse Stewart]

Dang truck is new again with more shiny stuff on the dash ...

 

[Jesse Stewart]

Going with a custom steering column firewall mount .. What I used when I install the 75 cutdown Cadillac column was the Caddy's Oem mount ..

This will look much better than what was ...

Hope to have the firewall og column hole patch welded in today ...

Looks like a few days of work will be needed ... Lots of holes to fill ..
Did get the column patch welded in .. Hadn't drilled the hole just yet for the new mount .. Soon will do a test fit ..

 

[Jesse Stewart]

Any of you Fellows still following this thread .. ??
Seems that I'm doing all the yakking !!

https://tenor.com/view/thread-revive-discord-discord-thread-threads-cpr-gif-22526300

 

[FDChappie]

Still here.

 

[Cheese]

Please keep posting -- very much enjoying your build!

 

[Jesse Stewart]

Glad too... And thanks ..

Well, the cat came back !!

Got the parts back from the closed up chrome shop, I'm sure going to miss those people for dang sure .. For over 40 years they took care of my plating needs, to me they were like family !

Here's a world of their work that my 52 Harley seen ...

So many motors I built seen their plating on em ...

Think I'll run the VDO bezel as is on the Pontiac vacuum gauge ..

Copper can be seen bleeding though in one spot ... Ain't no biggie ... Going to keep looking for a better bezel,

Tricking out the tach & vacuum gauges with convex glass lens ... The factory gauges have convex lens, a better look will be netted with all having the same look ...

Another item that I intended to have chrome was a switch bezel ..
This was dropped shipped to the chrome shop, I didn't get to see it, only from photos the seller sent to me ..
All the switch bezels on the dash were plated, thought was to keep all matching ..

Once it was in my hands seen that it was in great shape only 70 years of built up curd ..
A little TLC and I found good chrome under the dirt ...

Kind of hard to spot the new to me bezel ??

 

[Jesse Stewart]

Dash sure looks busy !
Two small items will bolt on under it ..
Not a pro job, but I'm happy with it ..

 

[Jesse Stewart]

The dome lens came in from the clock company ..

Think I can fit them to the tach & vacuum gauges ...
Got the same dome as the stock IH gauges, which is super cool !

Had to take about ..180" off the O.D. to get it to fit the tach ..

 

[FDChappie]

How are you going to get the bezels to fit with out bending them up???

 

[Jesse Stewart]

How are you going to get the bezels to fit with out bending them up???

The tach was super easy ... Pretty much was a snap-off, snap on deal ...
No bending the lip was involved ...

On the vacuum gauge, different story there ...
I bought just the bezel from a Speedo repair shop (Had a hell of a time finding one), it came to me with the lip deformed in order to get it off whatever gauge it was on ...

Don't look like there's enough lip to capture the gauge housing ..

My plan is to use Two Ton Epoxy to bond the bezel to the gauge housing flange ...
Did the best I could with striating out the deformed bezel lip ...

Hope to find a better Series 1 3-3/8" VDO bezel down the road, but as they say "A bird in the hand is worth two in the bush"

 

[Jesse Stewart]

Don't look like there's enough lip to capture the gauge housing ..

Going to explore a idea to gain some room for the lip to capture the gauge housing flange ..
Just might work and just might be needing to order another convex lens ??

Worth a try, not wanting to use the epoxy .. At least not yet !
Sure do wish I had a better bezel for this gauge ..

Ok ... After thinking about the bezel I'm trying to use, decided to sh*t-can it .. And keep searching for another VDO Series 1 3-3/8" tach just like the one I already have ....

Using the bezel from it will get rid of the ........

I may have located one ...
Soon to find out ... Was hoping to find it my state, shipping would get it here fast ...
But noooo, had to be in the Hot-Rod state of the U.S. ... Oh well, I consider myself very lucky to have found one ... Dang things are like a ....

 

[Jesse Stewart]

Cleaned up some ugly ..

Much, much better than what I had ..

 

[Jesse Stewart]

In order to net a clean looking engine compartment did some work filling unused holes on the inner fenders..

Engine bay side will see bed liner, tire side will have undercoating ..
After being sandblasted and a good coat of epoxy primer laid on ..

Already did the hood with bed liner ..

 

[Jesse Stewart]

Getting a bit more work done on the doors ..

Installing the cat whiskers is going well, did polish the Stainless some ..

Since the IH trucks didn't have a lot of shiny parts on them to begin with, thought why not ..

 

[Zaedster]

Lookin' good.

 

[Jesse Stewart]

Was needing some small parts for the Cadillac column ..
Tried to find Nos, but soon found out that 50 year old new Caddy parts have went with the Do-Do bird ..
Been looking for used ... Found a column from a 76 Eldo, although I'm not going to be using much from it, just a few internal parts ...

Might be using the steering wheel cause it has a woodgrain insert ...
That's a plus ... Matching the dashboard will add a nice touch

https://www.binderplanet.com/forums/index.php?attachments/1721106291424-png.253160/ ..

 

[Jesse Stewart]

Sure do wish I had a better bezel for this gauge ..

Ok ... After thinking about the bezel I'm trying to use, decided to sh*t-can it .. And keep searching for another VDO Series 1 3-3/8" tach just like the one I already have ...

I may have located one ...
Soon to find out ... Was hoping to find it my state, shipping would get it here fast ...
But noooo, had to be in the Hot-Rod state of the U.S. ...

The West Coast bezel didn.t pan out, but did get some numbers to call ..

One of those numbers was a shop on the East Coast and they have a Nos ... It's on order, be here in a few days ...
Dashboard is getting very close to being done, sure was a chore getting all the pats together to net the look I'm after ..

 

[Jesse Stewart]

Man, was this a chore ?!?

Not the work putting it together but finding the dang thing ...
Speed Shop in CA. hooked me up with a phone number, shop in NC had Nos bezels ...

Woodgraining is going well, now that I got my feet wet going to redo the dashboard & glovebox door ...
Wanted to see a better matching grain pattern from the two ..
Doesn't look all that bad the way it is, do think I'll be able to net a better match between the two pieces ...