R-100 4X4

[Jesse Stewart]

Pulled the trigger for the 4331 Hurst stick ..
It was being made for GM trucks .. Got a Nos one, still in skin warping on the way ..

Also on the way is the crossmember, tracking says tomorrow ..

In the mode of patching the old t-case shifter hole in the floorboard, bout done with that ..
Driveshafts are yet to do ..
Chipping away at it, sure feels good to be on the downhill slide with the tranny swap ..
( That was a colossal chore to do and very time consuming, I'm here to tell ya )

 

[Jesse Stewart]

Crossmember was a bogger to make it fit ..

Cut a half inch out of each side and welded back in ..

Was a bit of work to make it fit ..

 

[FDChappie]

Good progress!

 

[Jesse Stewart]

Transfer case shifter is in ..

Disguised as the transmission shifter ..
Trans shift is out of sight ... But can be seen in the photo ..

Got a cool knob for it that will match the dash woodgrain on order ..

 

[Jesse Stewart]

Since the overdrive trans is on the downhill slide almost got the column shift to work.
Welded the pivot in it's new location on the frame rail. That worked out super well, made the rod that runs up to the column lever work, it's a GM item off of a car, only needed to be bent in a few places ..
That's working really nice now ...

Did run up on a problem, working the column shift though all the gears, found that the 75 Caddy column didn't have enough throw for first & second gears ...
Worked fine when the TH400 was in the truck ..
Going to try cutting the slot that acts as a stop longer ..

Could move the hole in the crossover arm to gain more throw, but think that would most likely cause problems with the column's Oem switches that are in use ..
Got that work to do today .. Need to pull the fender & inner fender to gain access to the underside of the column .. Or remove the column from the truck ..

While the fender is out of the way, be great timing to install some beef to a known problem area on the frame ..

There's no damage on the frame, these plates will keep it that way ..

Beef installed ...

Almost, waiting for the bolt on brace ..

 

[Jesse Stewart]

Going to prep the dash for wood graining ...

Since I was working the Caddy's column for having all the gears to work on the 4L80, time to work the dash too ...

Must dial in the stops to get low gear to work ..

 

[Jesse Stewart]

Got a few holes to fill with weld ..

Headlight switch looks like it's going to work in the og starter switch hole ..
Got some work to get done on the fuel gauge switch before it will look like it belongs ..

 

[Jesse Stewart]

Steering box brace came in ..

That should add a world of beef to the box ...

 

[Jesse Stewart]

BTY ...

Won't be having the need to keep the Oem Caddy switches on the column anymore ..
Was wanting to keep them on line due to the harness from the GMC plugged right up on the Caddy column ..

But, with modifying the column to work all the gears on the 4L80E trans, didn't see how they could hang with the new amount of throw it has now ...

The cure was already in hand ...

Sometime back I bought a gear shift indicator from "Ron Francis" ... I got it to tell me what gear I was in ..

The unit also controls the neutral safety and backup lights !!
Problem cured ...

 

[Jesse Stewart]

Dash work is going well ..

Filling the gaps around the AC vents with All-Metal ...
Also the radio had gaps that was filled ..

Had about 20 holes to weld up ...
Soon will have the dash under primer ..

The A/C Pod and the install of the power cowl vent motor is next to do ..

 

[Jesse Stewart]

Pod is finally nailed on ...
Took a bit of work to dial in the fit ..

Gap is fairly large on the vent .. Using metal for filling up most of the crack ...

Getting closer to be seeing woodgrain .. !

 

[Jesse Stewart]

Gave the vent a slight tilt ...
Might help getting the air in the face better ... This vent only has side to side adjustable directional air flow, no up or down control ..

 

[Jesse Stewart]

Some primer a little sanding and it's ready for printing on the woodgrain ...
Stay tuned ... This just might be interesting ..
(Backup plan, Almond)

 

[FDChappie]

I had a 1933 DeSoto rumble seat coup that had awesome wood graining on the dash and window trim. Can't wait to see yours.

 

[Jesse Stewart]

Same here ...
Mine was a 48 Chevy Fleetmaster ...

This will be a first for wood graining ...
Hoping it will look good, going to burry it under a ton of clear ... Give it a deep look ..

 

[Jesse Stewart]

Anybody know what this switch controls ??

 

[FDChappie]

That looks like a fuel tank selector.

 

[Jesse Stewart]

Found a NOS one ...

I have the og left tank and a aftermarket 30 ga bed tank ...
Don't have the right tank, can't find one ..
Been thinking about taking another left tank and move the filler neck ..

There's a right side aux tank out there somewhere with my name on it ... I just haven't run up on it yet ..
Not looking forward to all the work it will take to convert a left side tank into a right side ..

 

[Jesse Stewart]

Thought it would be a good idea to slow down the rust .. Backside seen Por 15 applied ..

Getting closer to shooting the base coat ..

 

[Jesse Stewart]

Last check for fit ..