2010 Rallye Swap Meet

[Mochamike]

9" axle shafts
these are stock, 9" shafts.
5x5.5" lug pattern
28 spline
32.25" from wms to end of splines
bearings are the sealed style
mounting flange holes are 2.5"x3.5" (roughly)
$50

32 spline shaft & carrier
this came out of my rear d60 (from a 99 Ford e250 van).
It is an open carrier, 32 spline side, and has teeth on the carrier/next to the ring gear for abs.
Comes with good 3.54 gears as well.:grinpimp:
also a 37.75" 32 spline ff shaft.
$50 for both

Pair of stock spicer, Jeep wagoneer, Dana 44 shafts.
These are the offset (ps) type.
30 spline, 6 lug (Jeep, toyota, Chevy).
$25


pair of Ford d60 35 spline inner shafts (circa 1979).
These are stock/spicer shafts.
No joints or outers, splines look fine.
$75 (will trade for Chevy d60 inners)

 

[Mochamike]

I've got four driveshafts for sale.

All are 1310 non-cv style shafts.
Some with, some without u-joints.
A few of the joints maybe new (mostly grease-able, spicer I think), but have been in my rig as trail spares, so are beat up. Some are used, but still have life in them (can't tell them apart).

#1 is 33.75"-36.75" shaft with 3" tubes.
This is a new never used shaft. It wasn't painted, sat in my truck as a spare, so has some mild surface rust. I bought this from specialty parts of cordelia when they were closing. It's from some unknown Jeep application. I believe the joints to be new.
$100 oba

#2 is 45.5"-48.5" shaft with 3" tubes.
This came in my rig when I bought it (8+ years ago).
Sat outside for years, has 1 old joint in it.
$50 oba

#3 is 22"-31" square shaft (I think joints are new or slightly used), this was my trail spare.
$75 oba

#4 is 23"-34" square shaft, only 1 joint, with a slightly used spicer joint. This was my front ds with about 12-14 runs on it.
$75 oba

square shafts are 2" & 2.5" , with .25 wall (could be 3/16" but I don't think so).

Prefer not to ship.
Pick up in concord.

Pick of shafts (#1 on top, #4 on bottom)

 

[Mochamike]

These should fit standard 10 spline Dana 18 & Dana 20 transfercases.

Left to right:

10 spline d18/20 standard yoke (1310), used
$25
(the one with the dust shield & cv yoke are sold)

One 1310 style flange for d18/d20 parking brake (driveshaft side)
$25

Dana 18 6 spline bull gear
$30

all parts are used, obo.

 

[Mochamike]

Twin sticks
although new, these are rather old.
I bought them from another guy 3-4 years ago.
These have some scuffs & dings from being moved around a bunch, but I'm 99% sure they were never used.

He said they were for an atlas or Dana 300.

I had to fab my own, so they are for sale.
$100.

 

[Mochamike]

2 u-bolts (9"x4.5")
$20

2 Dana 44 drive flanges (no cap/hub covers)
$30


2.5" wide spring hangers (were cut off).
$20 (come with bushings). Pic above.

Shafts are gone.

 

[Mochamike]

I'll be bringing some of the above stuff to the rallye.

If your interested in any of it (even just a little), shoot me a pm & let me know so I can make sure I bring it.