IH PARTS AMERICA
Click Here!

Go Back   IH PARTS AMERICA > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Photo Gallery IH Store Home

Showing results 1 to 25 of 500
Search took 0.01 seconds.
Search: Posts Made By: Hondo
Forum: Axle Tech Questions 09-12-2019, 01:16 PM
Replies: 3
Views: 348
Posted By Hondo
Re: Wheel stud.

Wondering if you are running aftermarket rims with 5/8 mounting holes instead of 1/2. If that's the case you should get some larger 5/8 studs, or do what I did, get some bronze shaft bushings, 1/2"...
Forum: Bay Area Binder Society 09-10-2019, 06:26 AM
Replies: 8
Views: 594
Posted By Hondo
Forum: Electrical Tech 08-31-2019, 08:48 AM
Replies: 7
Views: 170
Posted By Hondo
Re: Problem starting engine

You have answered my question, and Scout Boys as well. Sounds like your wiring is mostly original and was working fairly well until recently. Your added ignition switch is basically jumping the...
Forum: Electrical Tech 08-30-2019, 09:25 AM
Replies: 7
Views: 170
Posted By Hondo
Re: Problem starting engine

Are you jumping the starter to get the engine to turn over? If you are using the key switch, there is power somewhere. There should be a fusible link, I believe coming up off of the starter's battery...
Forum: Ignition Tech 08-28-2019, 10:46 AM
Replies: 6
Views: 218
Posted By Hondo
Re: Random Misfire

Unless you've installed a new one recently, might want to check your fuel filter as well, especially since it is happening under load. Also the first ignitors tend to die if you leave the ignition on...
Forum: Transmission Tech 08-22-2019, 06:26 AM
Replies: 10
Views: 334
Posted By Hondo
Re: T-19 Shifting Question

At this point other things to check are your motor mounts and transmission mounts. If the motor or transmission are moving around it will raise havoc with your clutch linkage.
Forum: Transmission Tech 08-20-2019, 07:30 PM
Replies: 10
Views: 334
Posted By Hondo
Re: T-19 Shifting Question

Have you tried pulling the access cover off the bottom of the bell housing to try and see what's going on? A couple of other things to check if you take the access cover off is if the pressure plate...
Forum: Transmission Tech 08-13-2019, 11:09 AM
Replies: 10
Views: 334
Posted By Hondo
Re: T-19 Shifting Question

I'll agree that it sounds like a clutch or pilot bearing issue. There is also a spring in the T-19s top cover linkage that can break and cause you grief. I doubt it would get replaced in a typical...
Forum: Basic Tech Questions 08-13-2019, 10:38 AM
Replies: 17
Views: 448
Posted By Hondo
Re: what are those parts for ?

That is the windshield wiper fluid pump reservoir, should be a small electric pump under it.
Forum: Basic Tech Questions 08-13-2019, 05:18 AM
Replies: 17
Views: 448
Posted By Hondo
Re: what are those parts for ?

The radiator coolant overflow tank usually mounts on the driver side fenderwell between the battery and the brake master cylinder/vacuum booster.
Forum: Electrical Tech 08-12-2019, 11:35 AM
Replies: 1
Views: 166
Posted By Hondo
Re: Dash, Marker and Tail Lights out

Hi Jake. There are two rectangular rubber bulkhead connectors coming through the fire wall high up on the passenger side. Try unplugging and reseating these first. They are the source of your type ...
Forum: Bay Area Binder Society 07-20-2019, 11:46 AM
Replies: 5
Views: 800
Posted By Hondo
Re: B.A.B.S. Summer Picnic July 20 - Save the date

Any one planning on showing up?
Forum: Bay Area Binder Society 06-24-2019, 02:24 PM
Replies: 5
Views: 800
Posted By Hondo
Re: B.A.B.S. Summer Picnic July 20 - Save the date

Sounds good, I'll be there. Danika gave birth to Maliki a 6 pound 2 ounce baby boy last Monday, so I'm officially an old geezer grandpa.
Forum: Axle Tech Questions 06-18-2019, 11:07 AM
Replies: 12
Views: 628
Posted By Hondo
Re: Help needed - front axle id

Quick way to tell is the cover on the 30 is symmetrical, and the cover on a 44 is not. If you look at the cover on the 44 in the back you will see the difference.
Forum: Gas Engine Tech 06-15-2019, 05:11 PM
Replies: 24
Views: 2,224
Posted By Hondo
Re: Cluster F**k

Did you try replacing the distributor cap and plug wires? If you were getting shocked from the wires, they are probably toast. The Pertronix is going to give you a hotter spark, which will make bad...
Forum: IH Parts America Product Questions 04-24-2019, 11:55 AM
Replies: 2
Views: 383
Posted By Hondo
Re: Brake Combo Valve

Picture please, IHPA sells a few different proportioning valves. If the switch is reading open, the switch plunger should be centered. Don't believe it is a "reset" button per se. Probably a relief...
Forum: Bay Area Binder Society 04-04-2019, 06:03 PM
Replies: 3
Views: 483
Posted By Hondo
Re: Dinner meeting Tuesday April 9th Smokin Pig

Here is the flyer for the Buckeye Bonanza at Hollister Hills 5/30 - 6/2. Last year was a low turnout, first time they had the event, Area 5 was almost empty, less than 20 people camping. Basically...
Forum: Electrical Tech 03-22-2019, 06:04 AM
Replies: 6
Views: 1,892
Posted By Hondo
Re: El Cheapo Brighter Headlights

The 12VDC wires that that used to go to the headlights go to one side of the coil contacts on the relays to energize them, the other side of the relay coils go to ground. The 12 or 10 gauge wire...
Forum: Electrical Tech 03-19-2019, 06:17 PM
Replies: 6
Views: 1,892
Posted By Hondo
Re: El Cheapo Brighter Headlights

I made an L bracket to mount the relays on. One screw at the top to the right of the socket holds it in place, and the coils are also grounded there. Makes it easy to work on without pulling the...
Forum: Electrical Tech 03-19-2019, 05:59 AM
Replies: 6
Views: 1,892
Posted By Hondo
Re: El Cheapo Brighter Headlights

I mounted the relays between my battery and the firewall, and used the wires that used to go to the headlights to power the coils of the relays. Still need to make sure the pins on the bulkhead under...
Forum: Carb Tech 03-15-2019, 11:14 AM
Replies: 4
Views: 413
Posted By Hondo
Re: Replace or rebuild Holley 1920 on 232

I run a Weber 38 degas on my 258 and have no complaints. It's a two barrel with mechanical secondary. Might have issues finding an adaptor though.
Forum: Bay Area Binder Society 03-13-2019, 10:45 AM
Replies: 3
Views: 458
Posted By Hondo
Re: Dinner meeting Tuesday March 12th Smokin Pig

Hollister Hills Buckeye Bonanza Saturday June 1. They don't have much information posted yet. Last year they opened area 5 early on the Friday before and you could camp overnight for 5 bucks. You...
Forum: Carb Tech 03-03-2019, 08:05 AM
Replies: 17
Views: 969
Posted By Hondo
Re: 68 Scout 800, 152ci 4cyl, hesitates during acceleration

The best way to check the vacuum advance is with one of those small hand vacuum pumps that have vacuum gauges on them. I would also make sure the mechanical advance is working smoothly by...
Forum: Bay Area Binder Society 02-28-2019, 10:25 AM
Replies: 2
Views: 352
Posted By Hondo
Re: Hey Hondo....

I'd go Saturday or Sunday, been fighting a horrible head cold, so haven't been involved with setup this year.
Forum: Transfer Case Tech 02-27-2019, 04:14 PM
Replies: 31
Views: 8,162
Posted By Hondo
Re: speedo gears???????

I would try calling these guys, there web site looks like they have about everything for speedos.
Texas Industrial Electric Co.
11116 Watt Circle
San Antonio Texas 78233
Phone 210 654 4075...
Showing results 1 to 25 of 500

 

All times are GMT -8. The time now is 10:44 PM.