IH PARTS AMERICA
Click Here!

Go Back   IH PARTS AMERICA > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Photo Gallery IH Store Home

Showing results 1 to 17 of 17
Search took 0.00 seconds.
Search: Posts Made By: Captainkerber
Forum: Transfer Case Tech 07-31-2015, 11:22 AM
Replies: 11
Views: 3,524
Posted By Captainkerber
Re: Scout 80 Vibration on initial acceleration

It has been an ongoing problem I will try to check the drive shaft tomorrow evening. Thanks for the help.
Forum: Transfer Case Tech 07-30-2015, 06:15 PM
Replies: 11
Views: 3,524
Posted By Captainkerber
Re: Scout 80 Vibration on initial acceleration

Ok so a little more information the
gear ratio is 3.54
it is different from the front I do to put it in 4 wheel unless in sand.
The motor mounts and tranmission mounts are new
if I let the...
Forum: Transfer Case Tech 07-28-2015, 11:56 AM
Replies: 11
Views: 3,524
Posted By Captainkerber
Scout 80 Vibration on initial acceleration

I have a 1962 Scout 80 with a 152
the rear end has been change out to a Dana 44 off a Scout 2
when I let off the clutch to accelerate it vibrates pretty bad.
Looking at the driveshaft you can...
Forum: Transmission Tech 07-15-2013, 11:00 AM
Replies: 3
Views: 695
Posted By Captainkerber
Re: T90 gasket kit

Attached is a picture of two of the plastic washers.
Forum: Transmission Tech 07-13-2013, 11:59 PM
Replies: 3
Views: 695
Posted By Captainkerber
T90 gasket kit

Where do the four round plastic pieces go in the gasket kit for the t 90 for amscout 80.
Forum: Gas Engine Tech 09-04-2012, 07:43 PM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Ok I fininished honeing the cylinders and took new mesuerments. The cylinders are 3.888 or 3.889mm would you recommend just replacing rings or getting new oversized pistons. Although I only drive...
Forum: Gas Engine Tech 08-30-2012, 06:26 PM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Finally had time to pull the pistons. I had to clean a lot of carbon off but found the numbers stamped on them 216160-r1 the measurements on the pistons are 3 27/32. The cylinders I used a engine...
Forum: Gas Engine Tech 08-25-2012, 09:31 AM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Yes I can feel the ridge and you are exactly right about the nut. Apparently the missing nut I lost on the air filter found its way into the intake manifold. As soon as I heard the noise I knew...
Forum: Gas Engine Tech 08-24-2012, 11:22 AM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Attached is a pic of the combustion chamber.
Forum: Gas Engine Tech 08-24-2012, 10:39 AM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Lets try that again here are the pictures of the cylinders, pistons and buildup.
Forum: Gas Engine Tech 08-23-2012, 10:45 PM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

The engine is out and to my nice supprise what I thought was itching or grooves was carbon buildup. What is the best method to properly remove the buildup? Now I do have a lot of damage to the...
Forum: Gas Engine Tech 08-19-2012, 12:32 PM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Thanks for the info I am pulling the engine on Wednesday and I will get pictures of the etching up before then.
Forum: Gas Engine Tech 08-19-2012, 12:21 AM
Replies: 17
Views: 3,799
Posted By Captainkerber
Re: 152 engine removal

Thanks. Will do.
There is very minor etching on the cylinder wall of my number two cylinder do you know if it is possable to hone it yourself. I live on kauai hawaii and finding someone who can...
Forum: Gas Engine Tech 08-18-2012, 02:47 PM
Replies: 17
Views: 3,799
Posted By Captainkerber
152 engine removal

I am about to take out a 152 gas engine out of my 1962 Scout 80. I plan on rebuilding both the engine and three speed manual transmition. My question would it be easier to pull them both together...
Forum: Axle Tech Questions 03-30-2012, 02:39 PM
Replies: 1
Views: 1,095
Posted By Captainkerber
Rebuild kit for Dana 27 powrlok rear diff

I am looking for a rebuild kit with gears for powrlok limited slip differential Dana 27 carrier on a 1962 Scout 80. Anyone know where I can get one.
I know upgrading to a Dana 44 would be best...
Forum: Basic Tech Questions 10-26-2011, 10:30 AM
Replies: 4
Views: 2,989
Posted By Captainkerber
Re: What bikini Soft top would be best for my 1962 Scout 80

I just ordered the parts thank you I will let you know how it fits.
Forum: Basic Tech Questions 10-25-2011, 11:41 PM
Replies: 4
Views: 2,989
Posted By Captainkerber
What bikini Soft top would be best for my 1962 Scout 80

I am looking for a bikini top for my 62 Scout 80. It has a after market roll bar 45 inches from the front of the windshield. Any suggestions on what top and channel would work for me.

...
Showing results 1 to 17 of 17

 

All times are GMT -8. The time now is 04:46 PM.