IH PARTS AMERICA
Click Here!

Go Back   IH PARTS AMERICA > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Photo Gallery IH Store Home

Showing results 1 to 25 of 500
Search took 0.03 seconds.
Search: Posts Made By: Robert Kenney
Forum: Carb Tech 10-07-2019, 03:59 PM
Replies: 4
Views: 799
Posted By Robert Kenney
Re: Installing Holley 2300

yes on the thick gasket only. No sealant.

The studs should be screwed in ahead of time. Use two nuts threaded on the upper threaded end, tighten to each other and use the top nut to screw the stud...
Forum: Gas Engine Tech 10-05-2019, 12:21 PM
Replies: 6
Views: 251
Posted By Robert Kenney
Re: Identify Part

Since there are literally thousands of different vacuum tree possibilities, you would be best to build one out of pipe fittings to suit your configuration. Personally I like brass fittings but any...
Forum: Chit Chat 09-05-2019, 03:18 PM
Replies: 452
Views: 101,213
Posted By Robert Kenney
Re: New Members please check in here

Ffphil,
Welcome to out little slice of IH paradise.
Hope you enjoy playing with your new way back machine. There will definitely be a specific process to starting it up. The wrong one can hurt....
Forum: Gas Engine Tech 08-30-2019, 01:45 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

I found the cam card for my existing 152, originally built with the intentions of turbocharging.

33957
Forum: Gas Engine Tech 08-27-2019, 03:17 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

With the rolling over of your engine to 45*, you would improve the height further.
Forum: Ignition Tech 08-27-2019, 10:12 AM
Replies: 6
Views: 401
Posted By Robert Kenney
Re: Random Misfire

Can you describe the miss fire?
Is it like one cylinder is missing for some period of time or totally random?

Coil can fail a number of ways. The secondary (high voltage winding) dielectric...
Forum: Basic Tech Questions 08-25-2019, 01:59 PM
Replies: 3
Views: 350
Posted By Robert Kenney
Re: Cruise Control unit

It is physically broken? Would seem simple to evaluate, disassemble, clean, and lubricate.
Forum: Carb Tech 08-25-2019, 07:43 AM
Replies: 1
Views: 194
Posted By Robert Kenney
Re: Stock fuel pump for new fuel cell

The stock pump will be fine assuming it is in working order.
Forum: Gas Engine Tech 08-20-2019, 03:19 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

I can give you the measurements as it stands now for sure, rotating it to 45deg is an other thing.. It took quite a bit of finagling to get the engine to sit on the stand like it is in a scout 80. If...
Forum: Gas Engine Tech 08-19-2019, 03:50 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

All I have at the moment. Hope it helps.
Forum: Electrical Tech 08-19-2019, 09:58 AM
Replies: 2
Views: 270
Posted By Robert Kenney
Re: Key On Constant 12v Power Source

If you are certain there is not a resistance element in the positive coil circuit, you could use it. If there is a resistance element in that circuit, run a new wire from the same circuit feed at the...
Forum: Gas Engine Tech 08-18-2019, 03:12 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

I have then adapter in hand, fresh off the VMC. Works as expected. While this is a small turbocharger the adapter will allow multiple larger options down the road. The 152 IH with it's flow...
Forum: Carb Tech 08-17-2019, 08:00 AM
Replies: 1
Views: 201
Posted By Robert Kenney
Re: 1967 International SV345 Electric Choke Wiring

Connect it to ignition switch switched power supplied in the run position only. Do not connect it to the ignition coil + terminal wire. That circuit most likely has a resistance wire of ballast...
Forum: Transmission Tech 08-13-2019, 09:41 AM
Replies: 10
Views: 645
Posted By Robert Kenney
Re: T-19 Shifting Question

I assume the bell housing location pins are in place? The bell housing is flat and true (front and rear faces are parallel) and the transmission is locating correctly on the bore ID.

After reading...
Forum: Ignition Tech 08-06-2019, 05:54 PM
Replies: 4
Views: 386
Posted By Robert Kenney
Re: no ported vacuum port

Both ported and timed advance configurations were used. You have ported. If it works well I would leave it alone. You will need to unplug the advance vacuum to set initial timing.
Forum: Gas Engine Tech 08-06-2019, 05:48 PM
Replies: 24
Views: 2,587
Posted By Robert Kenney
Re: Cluster F**k

Are you referring to the oring that goes on the valve stem? Yes, I would renew them as well.
Forum: Gas Engine Tech 08-05-2019, 10:02 AM
Replies: 6
Views: 384
Posted By Robert Kenney
Re: Compression difference in a 345?

Don't disconnect the fuel line for a compression test.
Forum: Carb Tech 08-04-2019, 03:51 PM
Replies: 18
Views: 842
Posted By Robert Kenney
Re: for my california brethren, failed a smog and now a gross polluter

12-1 is rich 16-1 is lean. Stoic, ( the middle of the chart) is perfect so to speak. All fuel in the mix is burned in the stoichiometric air fuel ratio, less efficient burning raises CO and lowers...
Forum: Basic Tech Questions 08-04-2019, 01:55 PM
Replies: 3
Views: 312
Posted By Robert Kenney
Re: Wobbling Rear Tires

Hammered it on to the hub? Probably not seated or you could have bent the axle flange. Either way best to jack it up and see what is bent.
Forum: Basic Tech Questions 08-03-2019, 03:31 PM
Replies: 3
Views: 312
Posted By Robert Kenney
Re: Wobbling Rear Tires

Did it wobble before you worked on it? If not you likely caused on of the items you listed.
If you don't know, jack it up and see what is out of true.
Forum: Gas Engine Tech 08-03-2019, 03:27 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

I decided to have my turbo mount adapter made out side. Just don't have time to do it in house. It's in line at a friends CNC shop. Should see it in a week.
Forum: Axle Tech Questions 08-03-2019, 03:24 PM
Replies: 3
Views: 533
Posted By Robert Kenney
Re: Wheel stud.

Have you verified the hole sizes you are pressing the studs into? I assume the studs are ribbed where they press into the hub.
These are usually defined by the hole and such. Dorman has a nice web...
Forum: Carb Tech 07-31-2019, 11:13 AM
Replies: 18
Views: 842
Posted By Robert Kenney
Re: for my california brethren, failed a smog and now a gross polluter

Yes idle mixture. Be careful you're not on to lean either, that can cause a partial misfire that will pass unburnt fuel.

This chart is helpful in the diagnostic process.
Forum: Gas Engine Tech 07-30-2019, 01:07 PM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

I'll TIG weld a V-band bung to the plate and then attach the down pipe with V-band clamp.
Forum: Gas Engine Tech 07-30-2019, 05:09 AM
Replies: 194
Views: 38,715
Posted By Robert Kenney
Re: The Ultimate IH Fourbanger

Kind of a wait and see. I envision an air cleaner housing on the passenger side front inner fender. Still looking for a suitable one.
Turbo outlet, down and in between the middle two intake runners,...
Showing results 1 to 25 of 500

 

All times are GMT -8. The time now is 01:40 PM.