IH PARTS AMERICA
Click Here!

Go Back   IH PARTS AMERICA > IH Parts America Area > IH Parts America Build-Ups
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Photo Gallery IH Store Home

Reply
 
Thread Tools Display Modes
Old 01-25-2013, 02:08 PM   #1
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default IH Parts Americas 1-Ton Travelall

So the story goes......I've had this 1970 1200d 4x4 Travelall for about 8 years or more sitting out in a field at my parents house. I got it on a trade from Chad for a Scout II that I had at the time. I've always wanted to build this Travelall up with some one ton axles and finally the time had come. We had some suspension parts that were needing to be tried out so I finally had a good enough reason to pull the rig out of the field and get it cleaned up.

I needed it to be ready in time for the annual Binder Bee meet in the first week of July in brooks, oregon. Being the first of May I figured I had plenty of time to pull this off. After all I had been hoarding some parts for it for a few years now(nv4500 trans, mated NP205 transfer case, a Dana 60 front axle and GM 14bolt for the rear) so I didn't have to worry about chasing the main components down and the 392 ran really good especially for something that has just sat dormant for so long.



Aside from some surface rust the Travelall was otherwise 99% rust free. Even the original paint with some polishing had some luster left in it.



For some odd reason the Travelall was outfitted with a pickup rear bumper which looked hideous.



The spare tire was mounted under the rear of the vehicle which was odd as most Travelall's had their spares inside the passenger rear cargo area.



The exhaust was swiss cheese. Air shocks and a factory swaybar complimented the rear suspension.



The interior was in need of being freshened up. The carpet was showing its age and the original front buckets were replaced with some more modern seats.



The dash still looked real good. The royal blue interior was definitely a fancy upgrade for the 1970 Travelall.



The original headliner was badly sagging but still intact.



The back seat was decent. Just some misc junk to remove.



The engine compartment was still mostly original with just some cob webs to clean up.



The original hood insulation was still all there which really helps with noise control.



With the cob webs were some mud dauber nests that needed to be removed.

Attached Images
File Type: jpg 017.JPG (59.3 KB, 8483 views)
File Type: jpg 018.JPG (96.6 KB, 9168 views)
File Type: jpg 020.JPG (91.0 KB, 6598 views)
File Type: jpg 021.JPG (81.3 KB, 6470 views)
File Type: jpg 022.JPG (84.3 KB, 6432 views)
File Type: jpg 024.JPG (41.5 KB, 6395 views)
File Type: jpg 026.JPG (40.0 KB, 6299 views)
File Type: jpg 025.JPG (62.9 KB, 7139 views)
File Type: jpg 028.JPG (60.8 KB, 6255 views)
File Type: jpg 030.JPG (68.1 KB, 6365 views)
File Type: jpg 032.JPG (63.4 KB, 6380 views)
File Type: jpg 033.JPG (66.4 KB, 6384 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795

Last edited by ihpartsjeff; 01-30-2013 at 01:40 PM..
ihpartsjeff is offline   Reply With Quote
Old 01-25-2013, 02:24 PM   #2
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

After a thorough pressure washing of the Travelall's under carriage and engine compartment the aftermarket front seats were removed.



The back seat was removed as well in preparation for removal of the carpeting.



The rear cargo area still had the original rear rubber mat.



Remarkably the mat was still in real good condition.



What I love about our west coast rigs is the lack of rust and good clean floors. This one was no different.



Just some mild surface rust was found on both left and right side of the front floor area.





A mount for the aftermarket seat was welded to the floor which I removed.



The factory front seat mounts were reinstalled.



As well as the original front seats so that the Travelall could still be driven in and out of the shop.

Attached Images
File Type: jpg 036.JPG (69.7 KB, 6368 views)
File Type: jpg 037.JPG (63.8 KB, 6390 views)
File Type: jpg 038.JPG (57.8 KB, 6248 views)
File Type: jpg 039.JPG (60.2 KB, 6246 views)
File Type: jpg 040.JPG (57.0 KB, 6232 views)
File Type: jpg 041.JPG (58.6 KB, 6200 views)
File Type: jpg 042.JPG (66.2 KB, 6221 views)
File Type: jpg 043.JPG (38.6 KB, 6209 views)
File Type: jpg 044.JPG (56.0 KB, 6218 views)
File Type: jpg 049.JPG (57.7 KB, 6391 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-25-2013, 02:54 PM   #3
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

Under the rear floormat the surface rust was a little worse.



With the worst rust spot being found near the rear of the cargo floor.



After a thorough washing and rust preventative treatment applied the rear floor was good to go(for now).



The Travelall was brought into the shop so that the harder work could begin. I had already prepared a GM 14bolt differential with new 4.56 gears, an eaton posi and all new brakes. If you're curious why I went with a GM axle instead of keeping the original Dana 60 or going with a Dana 70(which I also had) was due to parts availability. Lets face it but GM brake and axle parts are much more common(and cheaper).



With the rear tires removed we could take a better look at things.





Starting with penetrating oil every nut and bolt was soaked down.



The rear suspension was typical for this type of rig. Heavy leafsprings, swaybar all on factory lift blocks.



The Travelall had the usual divorced new process transfer case that was in dire need of being re-freshened.



A t98 four speed looked the same as the transfer case.



The original front Dana 44 axle had the factory optioned tierod skid plate.

Attached Images
File Type: jpg 001.JPG (56.6 KB, 6177 views)
File Type: jpg 004.JPG (66.9 KB, 6172 views)
File Type: jpg 006.JPG (74.5 KB, 6217 views)
File Type: jpg 007.JPG (63.5 KB, 6253 views)
File Type: jpg 010.JPG (61.1 KB, 6146 views)
File Type: jpg 012.JPG (59.6 KB, 6146 views)
File Type: jpg 013.JPG (65.9 KB, 6167 views)
File Type: jpg 015.JPG (84.2 KB, 6580 views)
File Type: jpg 016.JPG (83.5 KB, 7414 views)
File Type: jpg 017.JPG (68.6 KB, 6256 views)
File Type: jpg 018.JPG (72.5 KB, 6184 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-25-2013, 03:14 PM   #4
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

First to go was that hideous truck bumper. It was a lot of torching and grinding but once off I was glad it was done.



Before the tear down of the rear axle and suspension I noted down some measurements so that I could get a jump on setting up the pinion angle on the new 14bolt.



The rear axle was removed next. Our welding table with wheels made the job a lot easier.



Next up was removal of the leaf springs.



A hole was needed to be drilled in order to have a way to fully remove the rear shackle bolt.



With the springs out the new springs could be compared along side the old.





Since most everything at this point had been removed I thought I would take the time to put a fresh coat of paint on the frame and undercoat the entire underside of the body.





The new springs were hung.



And with that the new GM axle could be brought in and installed.



Attached Images
File Type: jpg 019.JPG (62.9 KB, 6211 views)
File Type: jpg 021.JPG (36.0 KB, 6200 views)
File Type: jpg 023.JPG (62.8 KB, 6319 views)
File Type: jpg 024.JPG (63.1 KB, 6120 views)
File Type: jpg 027.JPG (71.6 KB, 6115 views)
File Type: jpg 030.JPG (28.8 KB, 6029 views)
File Type: jpg 029.JPG (27.5 KB, 6020 views)
File Type: jpg 031.JPG (78.0 KB, 6061 views)
File Type: jpg 032.JPG (63.8 KB, 6037 views)
File Type: jpg 034.JPG (73.4 KB, 5972 views)
File Type: jpg 035.JPG (61.7 KB, 5999 views)
File Type: jpg 038.JPG (75.9 KB, 5995 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-29-2013, 04:25 PM   #5
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

I did a quick check on how much lift the rear of the Travelall got with the new rear springs.



Back up in the air it was time to install some shock mounts. Since the stock style ubolts and plates were replaced with CPT that also meant the shocks mounts would need to be added.





I forget what that shock mount is from but we happened to have it and it fit nicely inside the frame rail.



As usual Bilstein 5150 shocks were installed as well as a set of CPT bumpstops.





The CPT bumpstops were an easy install. One hole drilled in each stock steel bumpstop and they bolted right in with a set of our bolt on mounting plates.



Last a CPT swaybar kit was installed.





Like the bumpstops only a couple holes were needed to be drilled and some tabs welded onto the Ubolt plates for the swaybar to be installed.

Attached Images
File Type: jpg 040.JPG (65.3 KB, 6201 views)
File Type: jpg 045.JPG (73.6 KB, 6053 views)
File Type: jpg 047.JPG (65.6 KB, 6004 views)
File Type: jpg 048.JPG (84.7 KB, 6127 views)
File Type: jpg 049.JPG (74.8 KB, 6068 views)
File Type: jpg 051.JPG (76.6 KB, 6128 views)
File Type: jpg 053.JPG (62.5 KB, 6004 views)
File Type: jpg 054.JPG (76.5 KB, 5975 views)
File Type: jpg 057.JPG (66.3 KB, 6031 views)
File Type: jpg 059.JPG (57.4 KB, 5910 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-29-2013, 04:49 PM   #6
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

One thing that I didn't want to deal with on this Travelall was the duel fuel tanks with each one needing to be filled on either side. Lets face it when you're in a crowded gas station and you're towing a trailer and you have to pull forward turn around and start the fueling process all over again its no easy feat. So both stock fuel tanks were removed for in favor of one huge tank mounted in the rear of the Travelall. For years I had been saving this supposed blazer military fuel tank which I believe was around 40 plus gallons. A simple strap and I was able to mock it up under the Travelall to take a look and see how it was going to fit.



Surprisingly with just a few modifications mounting the tank wasn't going to be that hard. First I welded on a mount to the front of the tank.





The way the tank had this extra upper support fit right up under the body made things simpler than I thought they would be.



I left the tank at that for now as I needed to order in a hitch and install it before finishing up the back side of the tank.



I had the whole front Dana 60 axle torn down before I realized that I didn't take any pictures of it. All parts were thoroughly cleaned and painted before being reinstalled.



Being a east coast axle it was pretty rusty and took a lot of work to make it look this good.





All assembled it was real nice having a solid and sturdy Dana 60 front axle underneath the Travelall with huge modern disc brakes.





Attached Images
File Type: jpg 062.JPG (62.1 KB, 6032 views)
File Type: jpg 073.JPG (61.6 KB, 5908 views)
File Type: jpg 074.JPG (48.9 KB, 5913 views)
File Type: jpg 075.JPG (55.7 KB, 5960 views)
File Type: jpg 076.JPG (51.6 KB, 5943 views)
File Type: jpg 093.JPG (104.9 KB, 5969 views)
File Type: jpg 094.JPG (91.4 KB, 6017 views)
File Type: jpg 095.JPG (75.8 KB, 6149 views)
File Type: jpg 102.JPG (69.9 KB, 6191 views)
File Type: jpg 104.JPG (71.3 KB, 5983 views)
File Type: jpg 103.JPG (53.6 KB, 5939 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795

Last edited by ihpartsjeff; 01-30-2013 at 03:34 PM..
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 11:20 AM   #7
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

With the Travelall turn around and back on the lift it was time to tackle the front axle and suspension.



It didn't take long to have the front axle assembly removed.





With the old springs out and set next to the new springs you can see how much more arch the new springs have plus how they are much longer.



The rivets that hold in the shackle hangers were ground down and removed so that they could be repositioned farther back on the frame.



The front spring hanger was modified as well.



New spring hangers were fabricated that were designed to be bolted in place of where the original ones were.



And bolted into place.



The shackle hangers were cleaned up and new busings installed.



With the shackle hangers bolted in the new CPT shackles and springs were installed.





With the leafsprings installed we were ready to install the front axle.

Attached Images
File Type: jpg 106.JPG (65.8 KB, 5966 views)
File Type: jpg 108.JPG (76.3 KB, 5804 views)
File Type: jpg 111.JPG (52.0 KB, 5810 views)
File Type: jpg 112.JPG (63.1 KB, 5916 views)
File Type: jpg 113.JPG (61.6 KB, 5968 views)
File Type: jpg 115.JPG (58.6 KB, 5752 views)
File Type: jpg 117.JPG (50.8 KB, 5822 views)
File Type: jpg 119.JPG (39.4 KB, 5738 views)
File Type: jpg 121.JPG (48.8 KB, 5799 views)
File Type: jpg 123.JPG (82.0 KB, 5857 views)
File Type: jpg 128.JPG (62.6 KB, 5884 views)
File Type: jpg 122.JPG (65.5 KB, 5756 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 11:47 AM   #8
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

CPT heavy duty 5/8" ubolts were installed along with some of our heavy duty Ubolt plates.





An off-the-shelf drop draglink was modified and installed along with some custom made brake lines, CPT bumpstops and Bilstein shocks.



I wanted a good all terrain tire with good street manners yet could hold their own offroad so I went with a set of near 35" tall goodyear duratracs on 17" steel wheels.



Back on the ground I could finally see what the Travelall was going to look like with its new lift and tires.





With the suspension and axles dealt with the next chore was the transmission and transfer case. As with the axles it was out with the old and in with the new.





With the clutch replaced and new rear engine mounts installed the nv4500 was slid into place. Like others I too was on a budget with this project and opted for going with a used transmission which I now wish I had paid the extra expense for a rebuilt one instead.



Instead of going with an IH divorced transfer case I opted to go with a mated transfer case. The particular transmission that I was using came out of a dodge 4x4 diesel pickup and was only used for a couple of years with the NP205 transfer case.



Since I had the transmission/transfer case combo for some time I forgot I had loaned out the adapter part of it. So while waiting to get it back I moved onto some other taks.

Attached Images
File Type: jpg 130.JPG (63.3 KB, 5802 views)
File Type: jpg 131.JPG (70.6 KB, 5871 views)
File Type: jpg 140.JPG (72.3 KB, 5846 views)
File Type: jpg 139.JPG (61.3 KB, 6144 views)
File Type: jpg 138.JPG (63.7 KB, 7516 views)
File Type: jpg 142.JPG (61.8 KB, 5991 views)
File Type: jpg 006.JPG (35.0 KB, 5755 views)
File Type: jpg 009.JPG (77.1 KB, 6107 views)
File Type: jpg 011.JPG (67.0 KB, 6630 views)
File Type: jpg 012.JPG (52.1 KB, 6560 views)
File Type: jpg 013.JPG (55.5 KB, 5689 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795

Last edited by ihpartsjeff; 01-30-2013 at 11:52 AM..
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 12:10 PM   #9
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

Another one of our CPT swaybars was installed in the front.



Hardest part on the install was welding on a pair of tabs for the links to mount to.



As well as a set of stan's headers.



The trailer hitch came in so that got promptly installed.



With the hitch installed the fuel tank modifications were completed. The rear most section of the tank had to be cut off as it was interfering with the hitch. Mounts were welded to each side of the tank and a simple filler neck was installed.



With it freshly coated inside and out fuel lines and such were installed in preparation for its install.



Next up was building the exhaust system.



Flex connectors were used on each side.



To a x-pipe.





And then ran out back to a pair of dynomax mufflers.



With the exhaust built it was removed for welding.



All the exhaust pieces welded up and ready for install.

Attached Images
File Type: jpg 028.JPG (99.2 KB, 5702 views)
File Type: jpg 029.JPG (90.4 KB, 5691 views)
File Type: jpg 030.JPG (79.1 KB, 5661 views)
File Type: jpg 034.JPG (88.6 KB, 5660 views)
File Type: jpg 032.JPG (57.6 KB, 5627 views)
File Type: jpg 033.JPG (62.2 KB, 5598 views)
File Type: jpg 037.JPG (80.4 KB, 5645 views)
File Type: jpg 038.JPG (61.0 KB, 5547 views)
File Type: jpg 036.JPG (72.9 KB, 5532 views)
File Type: jpg 035.JPG (69.5 KB, 5543 views)
File Type: jpg 043.JPG (66.3 KB, 5520 views)
File Type: jpg 069.JPG (77.4 KB, 5509 views)
File Type: jpg 072.JPG (64.3 KB, 5489 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795

Last edited by ihpartsjeff; 01-30-2013 at 03:37 PM..
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 12:44 PM   #10
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

The NP205 transfer case was torn down for inspection.





Everything on it looked amazingly well so it was cleaned up and reassembled with new gaskets and seals.





Next the transfer case was installed.



For those that May replicate this set up an ear on the top of the transfer case does hit the floor board and will need to be trimmed for proper clearance.



Since there was no way that I was going to hang that much weight off of the bell housing an additional transmission crossmember was fabricated.







For its basic design it works really well and is plenty strong enough.



I ended up going with this oem rubber transmission mount.



I had to build an adaper so to speak between the mount and tail housing of the transmission.



The crossmember was sleeved for easy access to the lower transmission mount studs.



The frame rail was drilled next.

Attached Images
File Type: jpg 070.JPG (82.0 KB, 5479 views)
File Type: jpg 071.JPG (84.6 KB, 5489 views)
File Type: jpg 078.JPG (69.7 KB, 5474 views)
File Type: jpg 079.JPG (69.6 KB, 5459 views)
File Type: jpg 085.JPG (52.9 KB, 5454 views)
File Type: jpg 084.JPG (71.0 KB, 5442 views)
File Type: jpg 080.JPG (78.1 KB, 5414 views)
File Type: jpg 081.JPG (72.0 KB, 5419 views)
File Type: jpg 087.JPG (76.8 KB, 5416 views)
File Type: jpg 089.JPG (65.2 KB, 5436 views)
File Type: jpg 090.JPG (62.6 KB, 5420 views)
File Type: jpg 091.JPG (48.1 KB, 5379 views)
File Type: jpg 092.JPG (64.7 KB, 5359 views)
File Type: jpg 093.JPG (61.2 KB, 5346 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 01:29 PM   #11
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

The existing transfer case shifter was slightly modified and used for shifting of the newer mated NP205 transfer case.



Some of our swaybar link parts was used and put together instead of using a piece of round rod like what the factory used.



A custom fuel tank filler was put together and installed along with a charcoal canister and fuel vapor recovery chamber.





Finally after roughly 6 weeks of off and on wrenching the Travelall was ready to be pulled out of the shop for its first test drive.





With little time to celebrate I needed to get the interior dialed in so it was pulled back into the shop.







The entire interior floor was sanded.



Attached Images
File Type: jpg 103.JPG (78.8 KB, 5405 views)
File Type: jpg 104.JPG (72.6 KB, 5375 views)
File Type: jpg 095.JPG (72.9 KB, 5386 views)
File Type: jpg 097.JPG (47.0 KB, 5358 views)
File Type: jpg 108.JPG (80.6 KB, 5329 views)
File Type: jpg 109.JPG (95.2 KB, 5350 views)
File Type: jpg 111.JPG (77.4 KB, 5378 views)
File Type: jpg 113.JPG (59.1 KB, 5333 views)
File Type: jpg 114.JPG (77.5 KB, 5327 views)
File Type: jpg 116.JPG (64.3 KB, 5321 views)
File Type: jpg 118.JPG (69.6 KB, 5329 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 02:19 PM   #12
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

With the remainder of the interior taped off primer was applied to all floor surfaces.





In preparation of the liner to be sprayed next all threaded holes were plugged.





Lately we have been using for spray liners a water soluble product called lizard skin. Lizard skin comes in two formulas, one for heat control and the other for noise control. We like to apply both for the utmost in noise and heat control.



For jobs like this we always call in our spray master michael.











Once applied and dry the lizard skin is mostly smooth to the touch.







Attached Images
File Type: jpg 119.JPG (90.0 KB, 5357 views)
File Type: jpg 120.JPG (49.6 KB, 5328 views)
File Type: jpg 122.JPG (33.3 KB, 5316 views)
File Type: jpg 123.JPG (36.8 KB, 5325 views)
File Type: jpg 127.JPG (65.7 KB, 5313 views)
File Type: jpg 132.JPG (80.9 KB, 5322 views)
File Type: jpg 133.JPG (59.7 KB, 5317 views)
File Type: jpg 135.JPG (68.5 KB, 5315 views)
File Type: jpg 134.JPG (67.4 KB, 5316 views)
File Type: jpg 136.JPG (69.6 KB, 5320 views)
File Type: jpg 141.JPG (58.4 KB, 5277 views)
File Type: jpg 142.JPG (51.6 KB, 5286 views)
File Type: jpg 143.JPG (53.2 KB, 5307 views)
File Type: jpg 144.JPG (51.0 KB, 5288 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 02:32 PM   #13
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

For the next line of defense against heat and noise several box's of hushmat were purchased.



Hushmat is a foil backed rubber insulator that comes in smaller rectangular sheets and is applied one sheet at a time.







It took some time but getting every square inch covered was well worth it.







And for yet another line of defense against heat a layer of thermoguard was laid down the center of the Travelall's passenger area so that heat from the exhaust or engine would not soak thru on those long road trips.







Attached Images
File Type: jpg 154.JPG (71.8 KB, 5266 views)
File Type: jpg 155.JPG (63.5 KB, 5276 views)
File Type: jpg 156.JPG (67.9 KB, 5277 views)
File Type: jpg 157.JPG (82.8 KB, 5298 views)
File Type: jpg 158.JPG (67.7 KB, 5271 views)
File Type: jpg 159.JPG (70.4 KB, 5292 views)
File Type: jpg 160.JPG (76.7 KB, 5284 views)
File Type: jpg 161.JPG (82.0 KB, 5281 views)
File Type: jpg 164.JPG (71.1 KB, 5224 views)
File Type: jpg 165.JPG (77.0 KB, 5274 views)
File Type: jpg 167.JPG (75.4 KB, 5260 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 02:57 PM   #14
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

Next up was the installation of the carpet kit.



The original shifter boot and door sill plates were reinstalled.





I was pretty happy with how well the aftermarket carpet kit formed to the floor.



The carpet kit also came with small pieces for the kick panel area.



I didn't like how the carpet came to an open end at the back cargo area so I used a rear mat sill plate from a Scout II to cover it up.



Since the rear rubber mat was still in good condition it was cleaned up and reused.





With the carpet done the seats were reinstalled.



With the transmission shifter and boot done and fire extinguisher in place the last few interior items were nearly complete.







All the door panels were removed and all window regulator and door latch's were lubed before being put back together.

Attached Images
File Type: jpg 168.JPG (61.3 KB, 5268 views)
File Type: jpg 169.JPG (69.2 KB, 5252 views)
File Type: jpg 173.JPG (90.3 KB, 5260 views)
File Type: jpg 174.JPG (95.2 KB, 5245 views)
File Type: jpg 175.JPG (77.7 KB, 5251 views)
File Type: jpg 176.JPG (97.8 KB, 5225 views)
File Type: jpg 177.JPG (72.0 KB, 5240 views)
File Type: jpg 178.JPG (71.4 KB, 5213 views)
File Type: jpg 179.JPG (89.7 KB, 5227 views)
File Type: jpg 180.JPG (89.3 KB, 5230 views)
File Type: jpg 181.JPG (68.5 KB, 5200 views)
File Type: jpg 182.JPG (78.3 KB, 5215 views)
File Type: jpg 183.JPG (76.2 KB, 5224 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Old 01-30-2013, 03:26 PM   #15
ihpartsjeff
Administrator & Owner
 
ihpartsjeff's Avatar
 
Join Date: Jan 2007
Member Number: 1
Location: Grass Valley, CA
Age: 44
Posts: 4,156
Default Re: IH Parts Americas 1-Ton Travelall

I had the Travelall back on the lift and while there I thought I would snap a few more pictures of the completed under-carriage.







The reason I had the Travelall back on the lift was for a caster change. After a few miles of driving I could tell that the caster was too far on the positive side so the front Dana 60 was unbolted and a shim change was made.



Since I planned on using the Travelall for traveling to shows loaded with parts and/or towing a trailer I wanted to be able to have the extra load capacity so a firestone air bag helper spring kit was purchased.



The kit consists of a pair of mounting brackets, air bags and some tubing for inflating the bags.



A few hours later I had the kit all installed.



Ideally the bag should have been mounted directly center over the rear axle but with so much going on between the swaybar and bumpstop I had to mount the bags where you see them.





Because of the lift I had to flip the upper frame brackets upside down. This caused the bags to rub the bracket so some trimming was required to make it all work.



One thing I wanted was the ability to alter the pressure in the bags on the fly so an onboard air compressor pacifically for these bags was installed.



The compressor was installed in the left rear quarter panel area left vacant by the fuel tank that was once there.





A gauge and control panel was installed in a convenient location that was easily accessible.

Attached Images
File Type: jpg 186.JPG (68.4 KB, 5212 views)
File Type: jpg 187.JPG (58.1 KB, 5217 views)
File Type: jpg 188.JPG (71.4 KB, 5200 views)
File Type: jpg 184.JPG (85.4 KB, 5227 views)
File Type: jpg 107.JPG (64.6 KB, 5211 views)
File Type: jpg 191.JPG (58.3 KB, 5201 views)
File Type: jpg 192.JPG (91.8 KB, 5213 views)
File Type: jpg 193.JPG (59.3 KB, 5187 views)
File Type: jpg 194.JPG (71.0 KB, 5190 views)
File Type: jpg 195.JPG (59.2 KB, 5180 views)
File Type: jpg 201.JPG (80.3 KB, 5181 views)
File Type: jpg 202.JPG (51.9 KB, 5194 views)
File Type: jpg 203.JPG (43.6 KB, 5162 views)
File Type: jpg 205.JPG (57.0 KB, 5191 views)
__________________

Jeff Ismail
IH Parts America - Owner
IH Sierra Fall Rallye Event Coordinator
Binder Books
CPT - Crawler Proven Technology
(530)274-1795
ihpartsjeff is offline   Reply With Quote
Reply

Thread Tools
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is Off



All times are GMT -8. The time now is 03:09 PM.