IH PARTS AMERICA
Click Here!

Go Back   IH PARTS AMERICA > Search Forums
Register FAQ Members List Calendar Search Today's Posts Mark Forums Read Photo Gallery IH Store Home

Showing results 1 to 25 of 500
Search took 0.05 seconds.
Search: Posts Made By: Robert Kenney
Forum: Axle Tech Questions 10-20-2018, 04:11 PM
Replies: 23
Views: 763
Posted By Robert Kenney
Re: Fixing Drunk Simulator

I always figure itís better to state the obvious and hope it is not taken wrong than to not and risk an unsafe situation. Iím glad you were going to fix her up right. 👍
Forum: Axle Tech Questions 10-20-2018, 02:37 PM
Replies: 23
Views: 763
Posted By Robert Kenney
Re: Fixing Drunk Simulator

Just to be clear, you do know that the leaf order in this photo is basakwards. :D

http://forums.ihpartsamerica.com/attachment.php?attachmentid=32827&d=1540061556

The order is from the main leaf...
Forum: IH Parts America News 10-20-2018, 10:38 AM
Replies: 23
Views: 1,209
Posted By Robert Kenney
Re: Submit Your Picture for the 2019 IH Parts America Annual CALENDAR!!!

Late I know.

The Rescue. Crowley Lake Basin, CA
32825

32826
Forum: Gas Engine Tech 10-18-2018, 04:08 PM
Replies: 12
Views: 376
Posted By Robert Kenney
Re: Oil "blow out" = Engine "Mis-Fire" ???

Only the mystery of the oil slick remains. I guess now you can run her and possibly track it down. 👍
Good job on getting her running well again.
Forum: Basic Tech Questions 10-18-2018, 04:04 PM
Replies: 3
Views: 146
Posted By Robert Kenney
Re: Engine power loss

Sounds a lot like fuel starvation. Check all of your fuel filters and if you can, verify fuel pressure at the carburetor fuel inlet.
Forum: Gas Engine Tech 10-13-2018, 12:15 PM
Replies: 12
Views: 376
Posted By Robert Kenney
Re: Oil "blow out" = Engine "Mis-Fire" ???

That is a ballast resistor. I donít think that is the original coil.
Forum: Gas Engine Tech 10-12-2018, 02:40 PM
Replies: 12
Views: 376
Posted By Robert Kenney
Re: Oil "blow out" = Engine "Mis-Fire" ???

When the plug wires get bad, the coil usually is what ultimately dies. Since the wire resistance gets high, the plug is no longer the easiest path to ground, the windings in the coil are end the...
Forum: Gas Engine Tech 10-11-2018, 05:19 PM
Replies: 12
Views: 376
Posted By Robert Kenney
Re: Oil "blow out" = Engine "Mis-Fire" ???

good pressure. FP it making the necessary pressure to fill your carb fine. We can ignore that for now.

I If you do not have a filter on the carburetor side of the fuel pump you are probably good...
Forum: Gas Engine Tech 10-10-2018, 01:11 PM
Replies: 12
Views: 376
Posted By Robert Kenney
Re: Oil "blow out" = Engine "Mis-Fire" ???

To check fuel pressure, you would need to plumb a pressure gauge into the fuel line before the carb.

A little fuel in the oil is not an issue as it will simply cook off. if it was a bunch you...
Forum: Gas Engine Tech 10-09-2018, 04:55 AM
Replies: 12
Views: 376
Posted By Robert Kenney
Re: Oil "blow out" = Engine "Mis-Fire" ???

It is possible you have a bad fuel pump. Many times when they fail they dump fuel into the engine. If enough fuel gets in the oil, it will boil off and blow oil out. Smell the oil for fuel. See if...
Forum: Axle Tech Questions 09-29-2018, 07:27 AM
Replies: 4
Views: 189
Posted By Robert Kenney
Re: Dana 27 vent

It is a small hole in the axle tube in the rear side of the tube. You can usually Iíd the location from a build up of oil residue and crud.
Forum: Ignition Tech 09-24-2018, 11:47 AM
Replies: 17
Views: 601
Posted By Robert Kenney
Re: 152 no distributor spark

That is where the draft tube is supposed to go. Looks like some one cut it off. The draft tube hangs down towards the bottom of the engine so the leaked combustion gasses can exit the engine and not...
Forum: Axle Tech Questions 09-08-2018, 03:37 PM
Replies: 23
Views: 763
Posted By Robert Kenney
Re: Fixing Drunk Simulator

I second the wedge removal. Also want to say that the way your spring pack is assembled is bad bad bad. The leaf order needs to be returned to its original order. Basically you only have a 2 leaf...
Forum: Transmission Tech 09-08-2018, 11:38 AM
Replies: 7
Views: 458
Posted By Robert Kenney
Re: 4th Gear 45mph Max Speed

So 4th being 1-1, My 68 in low range 4x4, 45 is top mph in 4th gear. Seems the most logical diagnosis that you are in low range. Already mentioned by other members.

If you have the single lever...
Forum: Gas Engine Tech 09-08-2018, 11:10 AM
Replies: 4
Views: 383
Posted By Robert Kenney
Re: Fuel Pump Rebuild Kit

Carter or Airtex, pictures please.
Forum: Reader's Ride's 08-26-2018, 07:20 PM
Replies: 166
Views: 5,029
Posted By Robert Kenney
Re: 1965 D1100 4x4 driver/project

I looked into the major brands. The last was the 400LE. That was replaced with an emissions safe formula and renamed. We would have to look at the standards that is meets. Thatís about all we can do...
Forum: Reader's Ride's 08-26-2018, 05:41 AM
Replies: 166
Views: 5,029
Posted By Robert Kenney
Re: 1965 D1100 4x4 driver/project

None of the current diesel oils have enough. I dug through all of the available data sheets to see what amount they had. Unfortunately, in recent months they have reformulated the few that did in an...
Forum: Basic Tech Questions 08-23-2018, 04:22 PM
Replies: 13
Views: 577
Posted By Robert Kenney
Re: Just Purchased - Am I nuts?

I don't know how much data is available on Canadian IH's but the US versions build year can be closely mapped by production sequence number. You can acquire the Line Setting Ticket and it will have...
Forum: Reader's Ride's 08-23-2018, 04:14 PM
Replies: 210
Views: 43,815
Posted By Robert Kenney
Re: 1964 Travelall and 1967 Travelette All Wheel Drive's

Now that the brakes are 120%, I am moving on to the drivetrain.
I want to replace all of the engine mounts to stop a rubbing/thumping issue that occurs while leaving from a stop. Also reseal this...
Forum: Basic Tech Questions 08-01-2018, 06:38 PM
Replies: 1
Views: 229
Posted By Robert Kenney
Re: 1975 500 (should I purchase?)

Hey CCCT, sounds like a good project.
Drive train wise, the axles should not be a big deal, the Eaton 5 speed is easier to source parts for than the IH built Fuller spinoffs. I really donít think...
Forum: Brake Tech 07-23-2018, 04:06 PM
Replies: 11
Views: 488
Posted By Robert Kenney
Re: Rear disc brake conversion issues

Assuming it is an adjustable rear prop valve, crank the adjuster in 1/2 of its range and try to bleed.
Forum: Basic Tech Questions 07-09-2018, 03:36 PM
Replies: 3
Views: 383
Posted By Robert Kenney
Re: 40 year scout owner

There was a time that I knew all of the good machine shops. Not anymore though. I have always done all of my own rebuilds. Sorry I couldn't be more help.
Forum: Basic Tech Questions 07-07-2018, 10:55 AM
Replies: 3
Views: 383
Posted By Robert Kenney
Re: 40 year scout owner

I would think, $5000 will cover it. Pull engine, rebuild and reinstall.
Forum: Gas Engine Tech 07-05-2018, 08:34 AM
Replies: 7
Views: 531
Posted By Robert Kenney
Re: Cluster F**k

In regards to your miss firing 2 and 4.
Have you verified the plug wire order? Possible that they got swapped. Also make sure the dizzy cap is not carbon tracking.

Regarding oil usage, two...
Forum: Ignition Tech 07-05-2018, 08:26 AM
Replies: 19
Views: 825
Posted By Robert Kenney
Re: Can't stop from Pinging

Good news...:thumbsup:
Funny, I'm heading out to verify the timing marks I created when building the 409 in one of my jalopy's. I had degree tape on the balancer but it departed at some unknown...
Showing results 1 to 25 of 500

 

All times are GMT -8. The time now is 01:47 AM.